닫기 

Display	Size(WxHxL)	96x96x68mm(3.8x3.8x2.68'') / 72x72x68mm(2.83x2.83x2.68'')
	PV/SP Display	4 Digit
Operation Mode		Program / Reset, 2 Zone PID
Control Mode		1CH Control
Max Channel		-
Pattern & Segments		2 Pattern / Max 30 segments
Input	TC	K, J, E, T, R, B, S, L, N, U, W, C, Platinel Ⅱ
	RTD	Pt100Ω, JPt100Ω
	Analog Voltage Input	-10~20mV, 0~100mV, 0.4~2.0V DC, 1~5V DC, 0~10V DC
Output	Control Output	RELAY, SSR(Voltage Pulse)
	Current Output	4 ~ 20mA DC
	Voltage Output	-
	Transmission Output	4 ~ 20mA (PV, SP, MV)
Digital Input	Contact Type	2 Points / 4 Types(RUN, HOLD, STEP, RESET)
	Contact capacity	-
Digital Output	Relay	Normal Open 30V DC A, 250V AC 1A Normal Close 30V DC3A 250V AC 3A
	Open Collector	ON voltage across contacts at less than 2V, the leakage current less than 100㎂
Sampling Time		250ms
Accuracy		±0.1% ±1% digit of Full Scale
Event	Alarm	1 Point / Max 3 Points(20 Types)
	Inner Signal	2 Points (PV, SP, TSP)
	Time Signal	1 Point
	Other	1 Point (RUN, Pattern END, UP, DOWN, SOAK)
Communication	Interface	RS485
	Protocol	PC-Link, MODBUS(ASCII, RTU), SYNC(Master, Slave)
	Speed	Max 115,200 bps
Power	Power	100 ~ 240V AC, 50 ~ 60Hz
	Power Consumption	Max 10W
Operating environment		-
Weight		-

Suffix Code
Model	Code	Information
GR200		Graphic recorder(applied touch panel function) 145(W)×145(H)mm / 5.71x5.71''
Input channel	2	2 channels
	4	4 channels
	8	8 channels
	12	12 channels

Model	GR200
Number of channels	2, 4, 8, 12 (Refer to the type configuration)
Input type	2 thermoresistors (Pt-100, KPt-100) 12 thermocouples (K, J, E, T, R, B, S, L, N, U, Wre 5-26, PL-II) 4 VDC (-10 - 20 mV, 0 - 100 mV, 1 - 5V, 0 - 30 V)
Sampling period	250 ㎳
Current to measure the thermoresistor (RTD)	About 0.21 ㎃
Input resistor	Thermocouple : More than 1 ㏁, VDC : More than 1 ㏁
Allowable wiring resistor	Thermoresistor : Maximum 100Ω/wire (The RTD is up to 10Ω/wire for the range of -100.00 - .150.00) Thermocouple : Less than 200 Ω VDC : Less than 2 ㏀
Impact of the wiring resistor	Thermoresistor : ±0.3 °C/10 Ω (The 3 lines have the same wiring resistors)
Allowable input voltage	Thermocouple : Less than ±10 V DC, VDC : Less than ±33 V DC
Degree	±0.15 % of F.S, ±1 digit (Except the RJC temperature error) ※ Refer to the input table
The error in the reference junction compensation (RJC)	±2.0 ℃ (0 ~ 50 ℃)
Sensor short detection (Burn-out)	UP-Scale for the short

Record accuracy		±0.5%F.S.
Alarm output		CH1(AL1, AL2), CH2(AL1, AL2) Relay out put(250 VAC/30 VDC 3 A 1 a)
Alarm output hysteresis		ON/OFF interval setting for alarm output: 1 to 999digit variable
Communication output		RS485 communication output(Modbus RTU protocol)
Set method		Setting by front keys
Sampling cycle		500 ms/channel x 2 channels = 1000 ms
Dielectric strength		2300 VAC 50/60 Hz for 1 min.(charging terminal of the other polarity)
Vibration		0.75 mm amplitude at frequency of 10 to 55 Hz (for 1 min.) in each of X, Y, Z directions for 1 hour
Relay life cycle		Mechanical: Over 5,000,000 operations, Electrical: Over 100,000 operations
Insulation resistance		Over 100 MΩ (at 500 VDC megger)
Noise resistance		Square shaped noise by noise simulator (pulse width 1 ㎲)±2 kV
Print	Method	Direct thermal line print
	Resolution	8 dot/mm
	Dots	384 dot/Line
	Life cycle	50 km
Record	Graphic mode	• Record speed(recording paper speed): 10, 30, 60, 120, 240, 480, 940 mm/hour • Memo cycle: 30 s, 1 m, 5 m, 10 m, 15 m, 30 m, 1 h, 2 h, 3 h, 4 h, 8 h, 16 h, 24 h
	Digital mode	TEXT mode record cycle: 00 m 05 s to 99 m 59 s
	Paper	Thermal Direct Receipt Paper (57 mm x 16 m)
	Paper supply method	Clamshell Type
	Language	Korean, English
Environment	Ambient temperature	0 to 50 ℃, storage: -20 to 60 ℃
	Ambient humidity	35 to 85%RH, storage: 35 to 85%RH
Approval		CE
Unit weight		Approx. 700 g